WARNING : Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer; Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood.
WARNING: This product can expose you to chemicals including nickel and lead, which are known to the State of California to cause cancer and lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
![[0, ]](/img/warning.png)
California Proposition 65
552-7 Scies cloches diamantée
552-7
Diamond grit edge hole saws have been specifically developed for professionals that need to drill extremely hard materials where it is increasingly difficult to drill with conventional hole saws.
These hole saws guarantee excellent performance and superior lifetime.
Also available as a 6-piece set 552-701-06, which contains:
These hole saws guarantee excellent performance and superior lifetime.
Also available as a 6-piece set 552-701-06, which contains:
Détails
Recommendations for use:
Turn on the drilling machine to start tool rotation. Begin drilling approximately at a 30° angle – this is the angle measured between the hole saw and the working surface. Cutting at an angle will prevent tool slippage, allow for perfect centering and increase cutting precision.
To gain improved stability through the drilling process, it is advised to rest the drilling machine on the working surface.
Continue the cut vertically, accompanying the tool in an orbital motion. This will favor better cooling and chip evacuation. (If you are using a guide, begin the cut vertically, then lift the guide and continue cutting in an orbital motion).
Remember that the tool you are using is not a drill bit. This means that attempting to bore holes perfectly perpendicular to the work surface on a frequent basis will drastically reduce the life of your hole saw.
Using water as a cooling agent may help extend the life of the hole saw.
The percussion/hammer action mode must be turned off when using these hole saws.
Variations
Filtrer
| Référence | D | I | L | S | MAX RPM | QTY | |
|---|---|---|---|---|---|---|---|
|
552-705
|
3/16 | 1-3/8 | 2-3/8 | 5/8 - 11UNC | 14000 | 10 | |
|
552-706
|
1/4 | 1-3/8 | 2-3/8 | 5/8 - 11UNC | 14000 | 10 | |
|
552-708
|
5/16 | 1-3/8 | 2-3/8 | 5/8 - 11UNC | 14000 | 10 | |
|
552-710
|
3/8 | 1-3/8 | 2-3/8 | 5/8 - 11UNC | 14000 | 10 | |
|
552-712
|
1/2 | 1-3/8 | 2-3/8 | 5/8 - 11UNC | 14000 | 10 | |
|
552-716
|
5/8 | 1-3/8 | 2-3/8 | 5/8 - 11UNC | 14000 | 5 | |
|
552-719
|
3/4 | 1-9/16 | 2-3/8 | 5/8 - 11UNC | 14000 | 5 | |
|
552-725
|
1 | 1-9/16 | 2-3/8 | 5/8 - 11UNC | 14000 | 5 | |
|
552-732
|
1-1/4 | 1-9/16 | 2-3/8 | 5/8 - 11UNC | 14000 | 5 | |
|
552-735
|
1-3/8 | 1-9/16 | 2-3/8 | 5/8 - 11UNC | 14000 | 5 | |
|
552-738
|
1-1/2 | 1-9/16 | 2-3/8 | 5/8 - 11UNC | 14000 | 5 | |
|
552-751
|
2 | 1-9/16 | 2-3/8 | 5/8 - 11UNC | 14000 | 5 | |
|
552-754
|
2-1/8 | 1-9/16 | 2-3/8 | 5/8 - 11UNC | 14000 | 5 | |
|
552-789
|
3-1/2 | 1-9/16 | 2-3/8 | 5/8 - 11UNC | 14000 | 5 |